This training course is based on (Rofin) WB lasers, (TR2500, TR3300, FPL3500 watts)
A letter from Dean (CEO & Owner of A Stellar Laser Service.)
Dear Possible Customers;
In the past I have seen many customers spend many thousands of dollars on
parts that were used for 2,000 hours that would have been lasted for 4,000 hours. Now it is not rocket science to under stand
that is big money. Also I have seen customers change turbines at a minimum cost of $35,000.00 instead of changing the bearings
this is a big expense that can be cut in a third by installing new bearings on site ($6,000.00 for parts) which is covered
in our training services.
Other training courses do not consult with the customer about the best money spent and when
the training is done they are impossible & costly to contact due to being over-seas. This training course comes
with one year (16 hours a day) support for lasers in the USA and this does include some holidays and weekends. Also we
will have available for customers to buy or rent all the tools as a package that is need for their laser. This will be discussed
on the first day before training begins. All of the documents that are needed, have been written by me and are very user friendly
with pictures specific areas.
This training course is $35,500.00 if you add up what others have charged for a Preventive
maintenance and not getting any training out of it. This training course would pay for it self from the start you would get
preventive maintenances done. Then you have personal to do the next two and then it would had paid for it'self, and you would
not have, to have down time waiting for a technician to show up this is the biggest money loss by company’s today is
down time. This training course would elimate that ever happing on your lasers again.
For your consideration:
1. Two weeks long (unless it includes turbine bearings to be
changed
then it will have to be longer.)
2. Will limit to
two students
3. Safety regulation
a. laser safety
b. safety concept, components
c.
high voltage
4.
Laser:
a.
theory of CO2 laser
b. general
function of CO2 lasers
c. components
5. Installation and operating resources:
a. easy access
b. power supply
c. laser gases, gas installation requirements
d. compressed
air requirements
e. cooling water requirements
6. Practical work:
a.
laser manual
b. external control/interface
c.
start-up and shut-down
process
d. programming CW and pulsing
e. service programs
f. messages and logbook entries
g. maintenance procedure
h. exchange of resonator optics
i. mode adjustment
j.
power adjustment
7. I will donate 10% to the diabetes foundation when all is paid in full for training program.
Test1:
CW-mode is selected at 3Kw
Inside the R-parameters value’s will appear
R13= The minimum tolerance of what the measured value should be
R14= The maximum tolerance of what the measured value should be
R15= The average power during this run.(This value must be used to compare with the below
indicated tolerances.)
Test2: Gated pulse-mode is selected at 3Kw with Laser program 25 (Piercing program)
Inside the R-parameters value’s will appear
R17= The minimum tolerance of what the measured value should be
R18= The maximum tolerance of what the measured value should be
R19= The average power during this run. (This value must be used to compare with the below
indicated tolerances.)
Test3: Gated pulse-mode is selected at 3Kw with Laser program 15 (Corner pulse program)
Inside the R-parameters value’s will appear
R21= The minimum tolerance of what the measured value should be
R22= The maximum tolerance of what the measured value should be
R23= The average power during this run. (This value must be used to compare with the below
indicated tolerances.)
Test4: Super pulse-mode is selected at 3Kw with Laser program 35 (Piercing program)
Inside the R-parameters value’s will appear
R25= The minimum tolerance of what the measured value should be
R26= The maximum tolerance of what the measured value should be
R27= The average power during this run. (This value must be used to compare with the below
indicated tolerances.)
Please contact us for a personalized training quote.
